CRUN Power Station Boiler (Grade A)
CRUN provides different sizes, different grades of medium and high pressure power station boilers and circulating fluidized bed boiler & boiler island.
Thursday, September 1, 2011
Listed Company CRUN/Industrial Boiler-240T/H CFB Boiler
240T/H high temperature industrial boiler :
1.Single steam drum
2.Circulating fluidized bed combustion
3.Natural circulation
240T/H high temperature seperating circulating fluidized bed boiler (industrial boiler) is with:
Single steam drum
Natural circulation
Circulating fluidized bed combustion
Semi open-air type arrangement
The boiler consists of a membrane walled combustion chamber, 2 sets of steel plate type cyclone separator and a rear part vertical shaft wrapped with air-cooled wrapping wall.
Inside the combustion chamber, panel type heating surface, 4 pieces of pipe panels for panel type super-heater and 3 pieces of water-cooled evaporating panels are provided.
The boiler is provided with a total of 4 sets of coal-feeding devices and 2 preformed limestone-feeding ports. All the coal-feeding device and limestone-feeding port are situated at the front part of the boiler, and are evenly arranged in cross direction on the tapered section at the lower part of the water-cooled wall of the front part wall.
The bottom part of the combustion chamber is a water-cooled air chamber made of water screen tube. Air conduit igniters are arranged behind the water-cooled air chamber. There are 2 sets of air conduit igniters, and in each, one high capacity ignition oil burner is provided. At 2 sides of the combustion chamber, 2 sets of air and water-cooling mode optional fly provided. 2sets of cyclone separators are arranged between the combustion chamber and the rear part vertical shaft, and the lower part of each separator, one set of J type valve feed back device is provided.
In the rear part vertical shaft, light and low temperature super-heaters, coal economizer and horizontal type air pre-heater are provided from top to bottom successively.
In the super-heater system, 2-stage direct-contact desuperheater is provided.
The whole body of the boiler is arranged symmetrically at the left and right side, suspended on the steel frame of the boiler, which is a space frame with subposts at the both sides.
1.Single steam drum
2.Circulating fluidized bed combustion
3.Natural circulation
240T/H high temperature seperating circulating fluidized bed boiler (industrial boiler) is with:
Single steam drum
Natural circulation
Circulating fluidized bed combustion
Semi open-air type arrangement
The boiler consists of a membrane walled combustion chamber, 2 sets of steel plate type cyclone separator and a rear part vertical shaft wrapped with air-cooled wrapping wall.
Inside the combustion chamber, panel type heating surface, 4 pieces of pipe panels for panel type super-heater and 3 pieces of water-cooled evaporating panels are provided.
The boiler is provided with a total of 4 sets of coal-feeding devices and 2 preformed limestone-feeding ports. All the coal-feeding device and limestone-feeding port are situated at the front part of the boiler, and are evenly arranged in cross direction on the tapered section at the lower part of the water-cooled wall of the front part wall.
The bottom part of the combustion chamber is a water-cooled air chamber made of water screen tube. Air conduit igniters are arranged behind the water-cooled air chamber. There are 2 sets of air conduit igniters, and in each, one high capacity ignition oil burner is provided. At 2 sides of the combustion chamber, 2 sets of air and water-cooling mode optional fly provided. 2sets of cyclone separators are arranged between the combustion chamber and the rear part vertical shaft, and the lower part of each separator, one set of J type valve feed back device is provided.
In the rear part vertical shaft, light and low temperature super-heaters, coal economizer and horizontal type air pre-heater are provided from top to bottom successively.
In the super-heater system, 2-stage direct-contact desuperheater is provided.
The whole body of the boiler is arranged symmetrically at the left and right side, suspended on the steel frame of the boiler, which is a space frame with subposts at the both sides.
1200W Household wind generators
1200W Household wind generators
(1) aesthetic appearance
(2) high technology
(3) light weight
(4) The breeze started
1200W Household wind generators
Hangzhou Shenle Technology Co., Ltd. is committed to
(1) wind energy into electricity,R & D and manufacturing Rather there Arts culture with Chinese characteristics, the landscape of wind turbine,Owns a number of patented technologies.(our engineering team will continue to design new products to meet the market demand, and pay attention to our website)
(2) production intelligent building public corridor electricity apportion device,This product development successfully solved completely corridor public electricity charges. Install this product will be massive saving electricity company charge link and labor cost.
About
Wind generator
Our wind generators are ancient Chinese culture art and modern science and technology, combining the perfect products, Strong visual and environmental photograph union, Have strong Chinese festival atmosphere of high-end products. Have China ceremoniously festal atmosphere of high-end products. Advanced design (maglev), Light weight, high efficiency and low noise.!
For our cities, villages, villas, road, tunnel, building, park, square, scenic spot, island, ships, the camps and mountainous place such as supply natural quiet green energy systems, Is a kind of energy conservation, environmental protection, landscaping of green energy.
Our mission
Since the industrial revolution, humans have already consumed much of the mineral resources, In recent years to various environment change in greenhouse gas emissions, excessive to make global warming, Cause a series of disasters, we shall review is no reflection in daily life's performance?
Everyone is the earth's people, please try your ability to energy consumption expenditure, don't forget to several thousand years later we children living environment.
As long as the earth rotates, the wind that is inexhaustible infinite energy so wind power will be benefit to global environmental efficient technology, we can in order to continuously innovation the technology but unremitting
(1) aesthetic appearance
(2) high technology
(3) light weight
(4) The breeze started
1200W Household wind generators
Hangzhou Shenle Technology Co., Ltd. is committed to
(1) wind energy into electricity,R & D and manufacturing Rather there Arts culture with Chinese characteristics, the landscape of wind turbine,Owns a number of patented technologies.(our engineering team will continue to design new products to meet the market demand, and pay attention to our website)
(2) production intelligent building public corridor electricity apportion device,This product development successfully solved completely corridor public electricity charges. Install this product will be massive saving electricity company charge link and labor cost.
About
Wind generator
Our wind generators are ancient Chinese culture art and modern science and technology, combining the perfect products, Strong visual and environmental photograph union, Have strong Chinese festival atmosphere of high-end products. Have China ceremoniously festal atmosphere of high-end products. Advanced design (maglev), Light weight, high efficiency and low noise.!
For our cities, villages, villas, road, tunnel, building, park, square, scenic spot, island, ships, the camps and mountainous place such as supply natural quiet green energy systems, Is a kind of energy conservation, environmental protection, landscaping of green energy.
Our mission
Since the industrial revolution, humans have already consumed much of the mineral resources, In recent years to various environment change in greenhouse gas emissions, excessive to make global warming, Cause a series of disasters, we shall review is no reflection in daily life's performance?
Everyone is the earth's people, please try your ability to energy consumption expenditure, don't forget to several thousand years later we children living environment.
As long as the earth rotates, the wind that is inexhaustible infinite energy so wind power will be benefit to global environmental efficient technology, we can in order to continuously innovation the technology but unremitting
Listed Company CRUN/Industrial Boiler-240T/H High Temperature Separating CFB Boiler
240T/H high temperature separating CFB boiler:
1.Single steam drum
2.Circulating fluidized bed combustion
240T/H high temperature seperating CFB boiler:
Single steam drum
Natural circulation
Circulating fluidized bed combustion
Semi open-air type arrangement
The boiler consists of a membrane walled combustion chamber, 2 sets of steel plate type cyclone separator and a rear part vertical shaft wrapped with air-cooled wrapping wall.
Inside the combustion chamber, panel type heating surface, 4 pieces of pipe panels for panel type super-heater and 3 pieces of water-cooled evaporating panels are provided.
The boiler is provided with a total of 4 sets of coal-feeding devices and 2 preformed limestone-feeding ports. All the coal-feeding device and limestone-feeding port are situated at the front part of the boiler, and are evenly arranged in cross direction on the tapered section at the lower part of the water-cooled wall of the front part wall.
The bottom part of the combustion chamber is a water-cooled air chamber made of water screen tube. Air conduit igniters are arranged behind the water-cooled air chamber. There are 2 sets of air conduit igniters, and in each, one high capacity ignition oil burner is provided. At 2 sides of the combustion chamber, 2 sets of air and water-cooling mode optional fly provided. 2sets of cyclone separators are arranged between the combustion chamber and the rear part vertical shaft, and the lower part of each separator, one set of J type valve feed back device is provided.
In the rear part vertical shaft, light and low temperature super-heaters, coal economizer and horizontal type air pre-heater are provided from top to bottom successively.
In the super-heater system, 2-stage direct-contact desuperheater is provided.
The whole body of the boiler is arranged symmetrically at the left and right side, suspended on the steel frame of the boiler, which is a space frame with subposts at the both sides.
1.Single steam drum
2.Circulating fluidized bed combustion
240T/H high temperature seperating CFB boiler:
Single steam drum
Natural circulation
Circulating fluidized bed combustion
Semi open-air type arrangement
The boiler consists of a membrane walled combustion chamber, 2 sets of steel plate type cyclone separator and a rear part vertical shaft wrapped with air-cooled wrapping wall.
Inside the combustion chamber, panel type heating surface, 4 pieces of pipe panels for panel type super-heater and 3 pieces of water-cooled evaporating panels are provided.
The boiler is provided with a total of 4 sets of coal-feeding devices and 2 preformed limestone-feeding ports. All the coal-feeding device and limestone-feeding port are situated at the front part of the boiler, and are evenly arranged in cross direction on the tapered section at the lower part of the water-cooled wall of the front part wall.
The bottom part of the combustion chamber is a water-cooled air chamber made of water screen tube. Air conduit igniters are arranged behind the water-cooled air chamber. There are 2 sets of air conduit igniters, and in each, one high capacity ignition oil burner is provided. At 2 sides of the combustion chamber, 2 sets of air and water-cooling mode optional fly provided. 2sets of cyclone separators are arranged between the combustion chamber and the rear part vertical shaft, and the lower part of each separator, one set of J type valve feed back device is provided.
In the rear part vertical shaft, light and low temperature super-heaters, coal economizer and horizontal type air pre-heater are provided from top to bottom successively.
In the super-heater system, 2-stage direct-contact desuperheater is provided.
The whole body of the boiler is arranged symmetrically at the left and right side, suspended on the steel frame of the boiler, which is a space frame with subposts at the both sides.
Listed Company CRUN/Industrial Boiler-35/3.82-M01M High and Low Speed CFB Boiler
High and low speed CFB boiler:
1.Water tube
2.Single steam drum
3.Natrual circulation
4.Indoor type
High and low speed CFB boiler introduction:
Water tube
Single steam drum
Natrual circulation
Indoor type arrangement
Boiling point combustion
The structure feature of the boiler is the adoption of the newly researched and developed design and technology of <<High & Low Speed "M" Type Circulating Fluidized Bed Boiler>> (hereinafter to be referred as M type boiler). The boiler has the merits of clean combustion with low pollutant emissin, and great reduction of wear of the heating surface.
It is so named as M type boiler, because the gas and smoke generated by the combustion of coal will pass 4 return runs: The hign temperature gas and smoke from coal burning flame go upward at high speed and then return to run downward to the bottom; they then turn upward again. At this time, under the centrifugal action at such turning of directions, the bigger sized fly ash grains are separated and drop into the low speed bed for burning. The gas and smoke generated at the high and low speed beds joint together and go upward and turn to horizontal flue on reaching the top, and they will then go through the rear flue to reach the bottom part of the boiler and then discharged into the chimney flue.The gas and smoke go through the 4 parallel return runs of up, down, up and down again, through which the complete processof ignition of the coal, combustion changing, separation, re-combustion, complete combustion, re-separation, circulation and cooling down.
1.Water tube
2.Single steam drum
3.Natrual circulation
4.Indoor type
High and low speed CFB boiler introduction:
Water tube
Single steam drum
Natrual circulation
Indoor type arrangement
Boiling point combustion
The structure feature of the boiler is the adoption of the newly researched and developed design and technology of <<High & Low Speed "M" Type Circulating Fluidized Bed Boiler>> (hereinafter to be referred as M type boiler). The boiler has the merits of clean combustion with low pollutant emissin, and great reduction of wear of the heating surface.
It is so named as M type boiler, because the gas and smoke generated by the combustion of coal will pass 4 return runs: The hign temperature gas and smoke from coal burning flame go upward at high speed and then return to run downward to the bottom; they then turn upward again. At this time, under the centrifugal action at such turning of directions, the bigger sized fly ash grains are separated and drop into the low speed bed for burning. The gas and smoke generated at the high and low speed beds joint together and go upward and turn to horizontal flue on reaching the top, and they will then go through the rear flue to reach the bottom part of the boiler and then discharged into the chimney flue.The gas and smoke go through the 4 parallel return runs of up, down, up and down again, through which the complete processof ignition of the coal, combustion changing, separation, re-combustion, complete combustion, re-separation, circulation and cooling down.
Listed Company CRUN/Industrial Boiler-410T/H High Temperature Separating Circulating Fluidized Bed Boiler
1. High temperature separating circulating fluidized bed boiler
2.Single steam drum
3.Circulating fluidized bed combustion
410 T/H high temperature separating fluidized bed boiler is with:
Single steam drum
Natural circulation
Circulation fluidized bed combustion
Semi open-air type arrangement
The boiler consists a membrane walled combustion chamber, 2 sets of steel plate type cyclone separator and a rear part vertical shaft (HRA) wrapped with air-cooled wrapping wall.
Inside the combustion chamber, panel type heating surface, 4 pieces of pipe panels for panel type super-heater and 3 pieces of water-cooled evaporating panels are provided.
The boiler is provide with a total of 4 sets of coal-feeding devices and 2 limestone-feeding ports. All the coal-feeding device and limestone-feeding port are situated at the front part of the boiler, and are evenly arranged in cross direction on the tapered section at the lower part of the water-cooled wall of the front part wall.
The bottom part of the combustion chamber is a water-cooled air chamber made of water screen tube. Air conduit igniters are arranged behind the water-cooled air chamber. There are 2 sets of air conduit igniters, and in each, one high capacity ignition oil burner is provided. At two sides of the combustion chamber, 2 sets of air and water-cooling mode optional fly ash discharging and slag cooling devices for multiple chamber type fluidized beds are provided. 2 sets of cyclone separators are arranged between the combustion chamber and the rear part vertical shaft, and at the lower part of each separator, one set of J type valve feed back device is provided.
In the rear part vertical shaft, high and low temperature superheaters, coal economizer and horizontal type air pre-heater are provided from top to bottom successively. In the superheater system, 2-stage direct-contact desuperheater is provided.
The whole body of the boiler is arranged symmetrically at the left and right side, suspended on the steel frame of the boiler, which is a space frame with subposts at both sides.
2.Single steam drum
3.Circulating fluidized bed combustion
410 T/H high temperature separating fluidized bed boiler is with:
Single steam drum
Natural circulation
Circulation fluidized bed combustion
Semi open-air type arrangement
The boiler consists a membrane walled combustion chamber, 2 sets of steel plate type cyclone separator and a rear part vertical shaft (HRA) wrapped with air-cooled wrapping wall.
Inside the combustion chamber, panel type heating surface, 4 pieces of pipe panels for panel type super-heater and 3 pieces of water-cooled evaporating panels are provided.
The boiler is provide with a total of 4 sets of coal-feeding devices and 2 limestone-feeding ports. All the coal-feeding device and limestone-feeding port are situated at the front part of the boiler, and are evenly arranged in cross direction on the tapered section at the lower part of the water-cooled wall of the front part wall.
The bottom part of the combustion chamber is a water-cooled air chamber made of water screen tube. Air conduit igniters are arranged behind the water-cooled air chamber. There are 2 sets of air conduit igniters, and in each, one high capacity ignition oil burner is provided. At two sides of the combustion chamber, 2 sets of air and water-cooling mode optional fly ash discharging and slag cooling devices for multiple chamber type fluidized beds are provided. 2 sets of cyclone separators are arranged between the combustion chamber and the rear part vertical shaft, and at the lower part of each separator, one set of J type valve feed back device is provided.
In the rear part vertical shaft, high and low temperature superheaters, coal economizer and horizontal type air pre-heater are provided from top to bottom successively. In the superheater system, 2-stage direct-contact desuperheater is provided.
The whole body of the boiler is arranged symmetrically at the left and right side, suspended on the steel frame of the boiler, which is a space frame with subposts at both sides.
Listed Company CRUN/Industry Boiler - 1025T/H High Temperature CFB Boiler
1025T/H high temperature separating CFB boiler:
1.Single steam drum
2.Open-air type arrangement
3.Natural circulation
1025 T/H high temperature separating type CFB boiler:
Single steam drum
Natural circulation
Circulation fluidized bed combustion
Open-air type arrangement
The boiler has 2 independent air chamber water-cooled walls and combustion beds, which integrated into a water-cooled wall combustion chamber, it also consists of 4sets of steel plate type cyclone separator and a part vertical shaft wrapped with air-cooled wrapping wall.
Inside the combustion chamber, panel type heating surface in installed. The boiler is provided with 4 coal-feeding ports and 4 limestone-feeding ports. The coal-feeding ports locate at the front part of the boiler and the limestone-feeding ports locate at two sides of the boiler, and are evenly arranged in cross direction on the tapered section at the lower part of the water-cooled wall of the front part wall.
The bottom part of the combustion chamber is awater0cooled air chamber made of water screen tube, which is connected with the igniters under the bed via metal expansion joint. There are a total of 2 sets of air conduit igniters, and in each, one high capacity ignition oil burner is provided.
At two sides of the combustion chamber, 2 sets of air and water-cooling mode optional fly ash discharging and slag cooling devices for multiple chamber type fluidized beds are provided.
2 sets of cyclone separators are arranged at two sides of the combusion chamber, and at the lower part of each separator, one set of "J" type valve feed back vertical shaft consists of wall wrapping tube wall. The rear part chimney flue is provided with high temperature superheaters, re-heaters, coal economizer and rotation type air pre-heater from top to bottom successively.
In the superheater system, multiple-stage direct-contact desuperheater is provided. In the
reheater system, emergency direct contact desuperheater and spray desuperheater are installed.
The whole body of the boiler is arranged symmetrically at the left and right side, suspended on the steel frame of the boiler.
1.Single steam drum
2.Open-air type arrangement
3.Natural circulation
1025 T/H high temperature separating type CFB boiler:
Single steam drum
Natural circulation
Circulation fluidized bed combustion
Open-air type arrangement
The boiler has 2 independent air chamber water-cooled walls and combustion beds, which integrated into a water-cooled wall combustion chamber, it also consists of 4sets of steel plate type cyclone separator and a part vertical shaft wrapped with air-cooled wrapping wall.
Inside the combustion chamber, panel type heating surface in installed. The boiler is provided with 4 coal-feeding ports and 4 limestone-feeding ports. The coal-feeding ports locate at the front part of the boiler and the limestone-feeding ports locate at two sides of the boiler, and are evenly arranged in cross direction on the tapered section at the lower part of the water-cooled wall of the front part wall.
The bottom part of the combustion chamber is awater0cooled air chamber made of water screen tube, which is connected with the igniters under the bed via metal expansion joint. There are a total of 2 sets of air conduit igniters, and in each, one high capacity ignition oil burner is provided.
At two sides of the combustion chamber, 2 sets of air and water-cooling mode optional fly ash discharging and slag cooling devices for multiple chamber type fluidized beds are provided.
2 sets of cyclone separators are arranged at two sides of the combusion chamber, and at the lower part of each separator, one set of "J" type valve feed back vertical shaft consists of wall wrapping tube wall. The rear part chimney flue is provided with high temperature superheaters, re-heaters, coal economizer and rotation type air pre-heater from top to bottom successively.
In the superheater system, multiple-stage direct-contact desuperheater is provided. In the
reheater system, emergency direct contact desuperheater and spray desuperheater are installed.
The whole body of the boiler is arranged symmetrically at the left and right side, suspended on the steel frame of the boiler.
Subscribe to:
Posts (Atom)